Polskie Forum FPV

like this https://www.dropbox.com/s/cgm1srxv32khip5/elektric%20shema3.jpg?m Ja bym masy do serw nie zapinał przez eleresa... Jak duży prąd, to może ścieżkę w PCB upalić (choć może AŻ TAK DUŻY to nie będzie:-)) A widziałeś ścieżkę masy na listwie w eLeReS'ie ? Mógłbyś na tym dystrybucję zasilania do ...

oke a redrawing https://www.dropbox.com/s/fqoa59qzalzdwnm/elektric%20shema2.jpg?m Edicao: chociaż po chwili zastanowienia nad pętlą masy, mkrawcz1 - chyba najsensowniej będzie zrobić tak: Czyli pewna , solidna masa grubszym przewodem z LiPo poprzez ESC do eLeReSa i z niego dystrybucja masy dla prądo...

oh thanks guy's i wil redraw my conection 's thanks for the help it wil be mutch better i see but there are thicker ground cabels must the be thicker in the real @mkrawcz1 - zobacz oryginalny rysunek i prześledź drogę masy - zadziała - masa idzie z baterii poprzez ESC i trafia do eLeReS'a. Nie ma co...

now the problem with the Rx module is solved i can look out how to wiring the hole hardware for fpv flying in the wing i have did a fast drawed diagram how i think wath the best is to do https://www.dropbox.com/s/le78ekm1ut8un3t/elektric%20shema.jpg?m and here my finisched case for the Tx module on ...

would this than a good ubec for powering the eleres 5v 5A http://www.hobbyking.com/hobbyking/store/__18789__5V_5A_UBEC_2_5S_Lipoly_6_23v_.html and next quastion i use a 2s lipo wath is the best way to power the Rx module the must conect on two servo's i want to use the Rx in a ritewing Better way wo...

SUCCESFULL hey man good news finaly everything went wel i had a succseful bind with the antenna's on it al the green leds wend on i tested here with a big old servo that i had and the transmission was oke on al channels thanks guy's for the support now i can look further ;) hey man your are fantasti...

hey man your are fantastic that trick worked like a charm that new flashing trick worked super good my Rx module is alive againe wwwooooooow now again trying to bind my modules with each other. that led flashing, how can i see when the binding is succes full i use this steps http://www.eleres.net/wi...

Exactly, so power is OK. If you can't find any break/short circuit in connections on board, I'm afraid that Atmega may be dead... i think it also. there is no optical damage on the module the Tx module works @ this time fine only the Rx module give it up what to do now can it be my fault i have not...

Obrazek Click to enlarge. Item described as MCP1703CB ("HUKK" on package, in middle bottom) has three pins. If you'll measure voltage between lower left (GND, also connected to servos' GND rail) and lower right, you should get around 3,30 Volts. if i good understand you and good masured i...

mkrawcz1 pisze:No, that pins are connected to stabiliser's input.
Output is connected to Atmega's pin no. 4

can you sent me a pic wath you mean sorry

mkrawcz1 pisze:Have you measured voltage on IC stabilisator's output? Should be around 3,30 Volts

no i dont
are that the pinheaders output for connecting the servo's?

Gentlemens, this is a Polish forum So what? We're not nationalists here. If we were, you'd be first to go - you are from UK, traitor :mrgreen: Nicky1980 can use the google translator. We both know how inaccurate this thing is. As for me - I prefer to read his posts even in chinglish than in botched...

hello i have a dead rx module can somone help me with it at the beginning i had it working al led's where flashing but when i taking time to find out for binding the Tx and Rx the led's wend out i dont connectet the powering wrong i think that it come's from my fingerprints on the electronics on the...

Nicky...this is the main thread of eleres: http://rc-fpv.pl/viewtopic.php?t=5202&postdays=0&postorder=asc&start=3210 Plz, write there next time.... o sorry thanks for the link but it's dificult to search en understand here the polich also wen it translated with google i think the RX mod...

done sended yesterday a couple of mails thanks for the reply hello i'am trying to setting up the eleres TX and RX module al power connections went good i had the red and green led's burning now when i trying to binding the tx and the rx what i not can find out wath i do wrong i don't understand the ...